To assemble a PC, it's good we have to know first the components of the PC itself. terlebihnya after understanding the components that then we do step - step assembly, as for preparation as follows
1. Preparation To Assemble
Before doing the assembly, then prepare beforehand all amenities like, Motherboards, Casings, Internal Components motherboard, screwdriver + / -, pasta fan, and all the equipment that will be needed
2. Assembles Processor
The first separate the first motherboard to the
casing, and then open the locking lever in the direction of the processor
socket and enter a period or segitiga.kemudian Squeeze until there is no gap
between the processor with the socket. after it scaled back the locking lever
3. Processor
Heatsink Assemble
Heatsink is very useful for removing
the heat generated by the processor, and therefore attach the heatsink to the
meeting at the top of the processor with a retaining clip as the first way
should coat the pasta / gel special heatsink fan on the contact surface. And
then lock the lever connecting clip on the heatsink and fan cable to the
connector on the heatsink fan connector on the motherboard.
4. Assemble Memory (RAM)
There are several types of memory
modules among other types of SIMM, RIMM, and DIMMs that can be distinguished on
the position of the arch side and bottom of the module. For how to install SIMM
types are as follows:
- Adjust the position lekungan on
the module with the tab slots.
- Enter the module by making a 45
degree oblique angle to the earlier slot.
- After the push to erect the module
in the slot, the locking lever that my yellow ring in the slot will
automatically lock the module
 |
5. Assemble The Casing Motherboard
Steps - steps to assemble the
motherboard to the case are as follows:
- Determine the position of the
holes for each holder plastic and metal. Holes for mounting metal (metal
spacer) is characterized by a ring on the edge of the hole.
- Attach metal or plastic holder on
the tray casing in accordance with the position of each corresponding mounting
holes on the motherboard.
- Place the motherboard on the
casing so that the head holder tray out of the holes on the motherboard. Attach
the locking screw on each metal holder.
- Attach frame I / O ports on the
motherboard.
- Replace the tray casing which is
mounted on the chassis and motherboard with screw lock.
6. Installing The Power Supply
The next step is the installation of
the power supply, as follows:
- Enter the power supply pad arak on
the back casing. Four pairs of locking screws.
- Connect the power connector from
the power supply to the motherboard. ATX power connector types have only one
way of installation so it will not be reversed. For non ATX type connectors
with two separate ground wires then black should be placed side by side and
mounted in the middle of the motherboard power connector.
- Connect the power cord for the fan
on the CPU cooler.
7. Cable Installation
- Put Power Connector Cable from
Power Supply to motherboard
 |
Attach the front panel power cable
|
Can you see abel front panel,
usually consisting of four kinds, namely:
• The LED Hard Drive (HDD LED)
• Power Button (Power SW)
• Reset button (RESET SW)
• The Power LED (POWER LED)
My article today will try to give
teachings on how to mounting the front panel, and my previous suggestions to
start you should have to be guided by using the manuals of the computer (CPU)
to avoid mistakes that cause damage to the motherboard by giving tips on how to
install small cables properly.
In general, where the cable port of
the panel is in the bottom corner (if CPU stand) and you have to find it really
consists of 10 pins with one pin located on the top right corner of an empty or
broken and almost all motherboards using the most current standards laying the
same in pin-pin cable to be fitted with panels, as sayatemukan some bersocket
ASUS AM2 mainboard (for AMD processors) which menngunakan arrangement unusual
and is rarely to be found.
once you find the pin Front Panel on
Mainboard, you'll have no trouble, generally located at the bottom edge of the
casing when dipasan mainboard. Lined in addition to pin berketerangan USB_1,
USB_2, AUDIO and others. Dibarisan Cobaah to find just the pins that have Front
Panel or F_PANEL information. Enough 2 photos below are examples of pin front
panel that are common in our environment, consisting of 10 pins with one pin
which is located in the upper right corner is empty, I often call it broken.
And nda can replace it with LOST or disappear and so if you want to
You can see below this
sketch the empty pin is pin number 10, and while the opposite end is pin number
1. So five pin under all the odd-numbered, and can be seen from left to right
while the 1-3-5-7-9 numbered pins on the top row of the even-numbered
2-4-6-8-10. And Keep in mind this number because you will not find on the
mainboard. You can just look in your mainboard's manual.
Here are gambarsusunan pin
that has given a number, remember the pin number 10 is blank so that you can
understand it more deeply
By using the above picture we can
connect the cable wires with each part, such as :
1-3 to the HDD LED cable
2-4 To the POWER LED cable
5-7 to RESET SW cable
6-8 To Cable POWER SW
While the pin number 9 leave it
blank. Note the left-hand column, Pin 1, 2 and 6 are connected to the positive
wire, only 5 pin number associated with the negative cable. In contrast, in the
right column only pin number 7 which is connected to the positive cable while
the pin numbers 3, 4 and 8 are connected to the negative cable. It is easy to
memorize, is not it? 1-3, 2-4, 5-7 and 6-8. Positive-negative,
positive-negative, negative-positive, and positive-negative. And been caught if
only pin numbers 5-7 are reversed from the other arrangement if you notice
there are only 3 pairs of cable installed in pin Front Panel, because the cable
to the POWER LED is not installed on the mainboard but directly connected to
the power supply
And how to find the positive and
negative wires? it is very easy you just see the color. Negative cable mostly
white or black. But if the white wire and the black to the white pair is the
negative cables. If there is no white or black cable will usually be red as
positive as his replacement cable
Judul:
The Procedure To Assemble The PC Components
Rating: 100% based on 99998 ratings. 5 user reviews.
Ditulis Oleh 13:39
Rating: 100% based on 99998 ratings. 5 user reviews.
Ditulis Oleh 13:39
